Uni-fiber News & Fiber Optic Cable Knowledge

What to Send for a Custom Fiber Cable Quote

Most quotation delays are not caused by price. They are caused by a missing parameter that has to be asked for, and then answered, before a specification can be confirmed.

Can Fiber Optic Cable Fiber Count Be Customized

Fiber count is one of the most commonly customized parameters — but it is not free of consequences. It changes the tube layout, and therefore the diameter, weight and mechanical design.

How Fiber Count Affects Fiber Optic Cable Diameter

Fiber count and diameter move together, but not smoothly. The diameter changes in steps, because tubes are added in whole numbers.

How to Specify a Custom Fiber Optic Cable

A custom cable specification is not a wish list. It is a set of constraints that the construction has to satisfy at the same time, and supplying them in order saves a round of questions.

What Determines Fiber Optic Cable Diameter

Cable diameter is not chosen for its own sake. It is the result of what has to fit inside the cable and how much protection the route requires.

How to Choose an Outdoor Fiber Optic Cable

Outdoor cable selection is decided by the installation method first. This guide works through the four decisions that narrow the range — how the cable is installed, what mechanical risk it faces, how many fibers are needed and what sheath suits the environment.

How to Choose a Fiber Patch Cord

A patch cord is a small purchase with a large effect if the wrong one arrives: it will not mate with the ports, or it will add loss or reflection to the link. This guide works through connector, fiber, polish and jacket, then length.

GYTA vs GYTS vs GYFTY Fiber Optic Cable

GYTA, GYTS and GYFTY are outdoor loose tube cable families that differ in one decisive area: whether the cable contains a metallic armor. That single difference decides where each one can be installed.

MTP/MPO Trunk Cable vs Duplex Patch Cord

Trunk cables and duplex patch cords are not competing products — they occupy different layers of the same installation. Understanding which layer does what is what determines the cabling design.

Central Loose Tube vs Multi Loose Tube Fiber Optic Cable

Both constructions protect fibers in gel-filled tubes. The difference is how many tubes there are and how the fibers are organized inside the cable — which changes fiber capacity, tube-level management and how the cable behaves during installation.

What Is an MTP MPO Trunk Cable

An MTP/MPO trunk cable is a pre-terminated multi-fiber cable with one MPO connector at each end, used as the fixed backbone between patch panels and cassettes. This article explains what it is, how the connector works and what has to be decided before ordering.

What Is a Fiber Distribution Box FDB

A fiber distribution box (FDB) is an outdoor enclosure where a feeder or distribution cable is terminated and split into drop cables serving individual subscribers. This article explains its role in an access network, how it differs from a splice closure, and what to confirm when ordering.

Armored vs Dielectric Fiber Optic Cable

Armored and dielectric cables differ in one decisive way: whether metallic protection is present. That single difference changes mechanical protection, earthing requirements and where the cable can be installed. This article sets out the comparison on structure rather than on marketing claims.

What Is ADSS Fiber Optic Cable

ADSS stands for All-Dielectric Self-Supporting. It is an aerial fiber optic cable that supports its own span load without a separate messenger wire and contains no metallic parts. This article explains the structure, what it is used for, and when it is the right choice.

What Is an Optical Distribution Frame (ODF)

An optical distribution frame (ODF) is the termination and cross-connection point for fiber cables inside a building. It converts loose-tube cables arriving from outside into organized, patchable ports.

Flat Drop vs Round Drop vs External Drop Cable

Flat drop, round drop and external drop cable are three answers to the same last-mile problem. They differ in cross-section, strength member and how the route is supported. The right choice follows from the route, not from the cable name.

How to Choose an FTTH Drop Cable

Choosing an FTTH drop cable is an installation decision more than a catalog decision. The route determines the cross-section, the strength member and the jacket, and those three choices determine the part you order.

ODF vs Fiber Distribution Box (FDB)

ODF and FDB are both fiber management products, but they sit at different points in the network. The ODF is the central-office or equipment-room cross-connect point; the FDB is a field distribution point closer to the subscriber.

What Is Figure 8 Fiber Optic Cable

Figure 8 fiber optic cable is an aerial cable whose cross-section combines two elements in a single sheath: a fiber optic unit and a steel messenger wire. It is installed by lashing or suspending the messenger between poles, so the messenger carries the mechanical load and the optical unit simply follows it.

What Is FTTH Drop Cable

FTTH drop cable is the final cable segment in a fiber to the home network. It runs from a distribution point or a fiber access terminal to the subscriber premises, and it is built to be small, flexible and easy to route into a building.

How to Choose an MTP/MPO Trunk Cable

A trunk cable is built to your channel plan, so the specification has to be right before the order is placed: fiber count, polarity and gender are fixed at build time and cannot be corrected in the field.

How to Choose an ADSS Fiber Optic Cable

ADSS selection is driven by the span, not by the catalog. This guide sets out the four decisions that determine the cable: the mechanical case, the fiber requirement, the sheath and the fittings.

ADSS vs Figure 8 Fiber Optic Cable

ADSS and figure-8 cables are both installed between poles, and both avoid a separate supporting wire. They are not interchangeable: one is all-dielectric and the other contains a steel messenger. This article sets out the structural difference, the installation implications and the selection boundary.

What Is a PLC Splitter

A PLC (Planar Lightwave Circuit) splitter is a passive optical device that divides one input across several outputs without any power supply. It is the component that lets a passive optical network share one fiber among many subscribers. This article explains the technology, the package formats and the selection factors.

Uni-fiber news

We'll participate in CIOE 2024 in shenzhen from 11th~13th Sept.